Reply To: EZSrve always Displays EZRain Valve 1 Run Times as 0 2017-12-21T14:54:20+00:00

HOME Forums Gateways EZSrve EZSrve always Displays EZRain Valve 1 Run Times as 0 Reply To: EZSrve always Displays EZRain Valve 1 Run Times as 0

Anonymous
Post count: 7

Hi Paul:

Hopefully this is the data you are looking for. I collected this data in 6 steps:

1. Connect the SHN Utility to EZRain and perform an SHN Utility query of the valve times
2. Navigate to Device Management and click config on EZSrve
3. Perform an EZSrve query of the valve times
4. Commanding a change of valve time 1 to “60” through EZSrve
5. Performing another Query through EZSrve observe valve time 1 is now shown as “0”
6. Performing another query through the SHN Utility and observe the correct data of “60”

The SHN utility was connected through the EZSrve. I left the SHN Utility open while I entered the commands in EZSrve. Unfortunately, I couldn’t see the traffic sent from the EZSrve in this configuration.

Let me know if I can provide any additional information.

___________________________

1. Received traffic from EZRain (05.EB.74) upon entering ID into SHN Utility and query for Max Manual Zone Run Times. After pressing “Get,” Zone 1 time is 23 minutes. This is a correct value that I had previously set in the unit.

from ID:05.EB.74 flags:2B cmd1:28 cmd2:0
from ID:05.EB.74 flags:2B cmd1:2B cmd2:23
from ID:05.EB.74 flags:2B cmd1:28 cmd2:0
from ID:05.EB.74 flags:2B cmd1:2B cmd2:17
from ID:05.EB.74 flags:2B cmd1:2B cmd2:1E
from ID:05.EB.74 flags:2B cmd1:2B cmd2:1E
from ID:05.EB.74 flags:2B cmd1:2B cmd2:1E
from ID:05.EB.74 flags:2B cmd1:2B cmd2:14
from ID:05.EB.74 flags:2B cmd1:2B cmd2:15
from ID:05.EB.74 flags:2B cmd1:2B cmd2:1E
from ID:05.EB.74 flags:2B cmd1:2B cmd2:21

2.Start EZSrve, navigate to Device Management, select the area “Irrigation Control” and then click Config:

from ID:05.EB.74 flags:2B cmd1:44 cmd2:9
from ID:05.EB.74 flags:2B cmd1:44 cmd2:7

3. Select Manual Max from Valve Run Time drop down menu and click “Get Data”

from ID:05.EB.74 flags:2B cmd1:45 cmd2:0

Note: At this point, Valve 1 is displaying “0” while valves 2-8 display the correct values. WRONG, Valve 1 time should be 23 seconds

4. Enter 60 in valve 1 and click “Write”

from ID:05.EB.74 flags:2B cmd1:40 cmd2:0

Note: At this point, the valve 1 value is displayed as “60” So far so good

5. Now click Get Data to read back the values from EZRain

from ID:05.EB.74 flags:2B cmd1:45 cmd2:0

Note: At this point, the Valve 1 value now is displayed as “0” WRONG, should be 60

6. Now use the SHN utility to query the EZRain Max Manual run times

Data sent to EZRain:
To ID:05.eb.74 flags:0F cmd1:28 cmd2:0
To ID:05.eb.74 flags:0F cmd1:2B cmd2:0
To ID:05.eb.74 flags:0F cmd1:2B cmd2:1
To ID:05.eb.74 flags:0F cmd1:2B cmd2:2
To ID:05.eb.74 flags:0F cmd1:2B cmd2:3
To ID:05.eb.74 flags:0F cmd1:2B cmd2:4
To ID:05.eb.74 flags:0F cmd1:2B cmd2:5
To ID:05.eb.74 flags:0F cmd1:2B cmd2:6
To ID:05.eb.74 flags:0F cmd1:2B cmd2:7

Data From EZRain:
from ID:05.EB.74 flags:2B cmd1:28 cmd2:0
from ID:05.EB.74 flags:2B cmd1:2B cmd2:3C
from ID:05.EB.74 flags:2B cmd1:2B cmd2:1E
from ID:05.EB.74 flags:2B cmd1:2B cmd2:1E
from ID:05.EB.74 flags:2B cmd1:2B cmd2:1E
from ID:05.EB.74 flags:2B cmd1:2B cmd2:14
from ID:05.EB.74 flags:2B cmd1:2B cmd2:15
from ID:05.EB.74 flags:2B cmd1:2B cmd2:1E
from ID:05.EB.74 flags:2B cmd1:2B cmd2:21

Note: At this point, the valve 1 value shown in the SHN utility is displayed as “60” This is CORRECT.